<wbr id="5eyqo"></wbr>

<rp id="5eyqo"></rp>
  1. <rt id="5eyqo"></rt>

    <tt id="5eyqo"></tt>
    <video id="5eyqo"></video>
    English | 添加收藏 | 設為首頁
    您所在的位置:網站首頁 > > 產品中心 > 彈性體材料 > TPE熱塑性彈性體EPDM/PP熱塑性彈性體 EP-3000
    EPDM/PP熱塑性彈性體 EP-3000
    Thermoplastic EPDM/PP Elastomeric Compound...
    型號:0

    參考價:¥

    說明:如您對該產品感興趣,請在此輸入您的手機號將本產品的地址 發送至您手機上。
    Product Description 產品描述
    EP-3000 series are dynamic vulcanized compound by EPDM and PP. It is also called thermoplastic TPV. They has various excellent properties such as good climate-resistant (UV, ozone, sunshine, rain), anti-aging, anti-moisture, chemical resistant (acid, alkali, alcohol, ether) and electrical property. Their cold-resistant property is very well and can be worked in -40℃~125℃for long time. EP-3002 and EP-3003 are medium level oil-resistant. The hardness of the series can reach 75A-40D.
    EP-3000是三元乙丙膠與聚丙烯(EPDM/PP)的動態硫化共混物,又稱熱塑性硫化橡膠(TPV),具有硫化橡膠的各種優異性能,有卓越的耐侯性(紫外線,臭氧,日光,雨水)耐老化,耐水性,耐化學品(酸、堿、醇、醚)和電性能。耐低溫性能卓越,能在-40℃~125℃的溫度中長期工作。其中3002和3003有中等耐油性。硬度范圍可以做到:75A-40D。
     
    Product Application 產品用途
    l  Insulation and jacketing of DC control cables, rail cables
    l  Insulation and jacketing of port machine cables, vessel cables and high-voltage submarine cables
    l  Injection mold parts of cables and jacketing of container lorry cables
    l  Car rubber parts: seal, exhaust pipes and interior decoration parts
    l  Water-proof coiled material of architecture, seal of refrigerator
    l  直流控制電纜,軌道交通電纜絕緣和護套
    l  港機和船用電纜,高壓海底電纜的絕緣和護套
    l  電纜注塑件,集卡電纜護套
    l  汽車橡膠件:密封條,排風管,內飾件等
    l  建筑用防水卷材,冰箱密封條
     
    Process Condition 加工要求
    Model
    牌號
    Machine Barrel Temperature
    機筒溫度
    MoldingTemperature
    機頭溫度
    Melt Temperature
    熔體溫度
    EP-3000 150 ℃– 190 ℃ 195 ±5℃ 185±5℃
    Above data is just for your reference and need to be adjusted according to the actual situation.
    以上加工條件只是參考,具體需根據實際情況做適當調整。
     
    Dry Condition 干燥條件
    No need for drying in normal environment. If the compound was affected with damp, dry it under 90℃conditions for 2-3 hours or under 70-80℃conditions for 3-4 hours. Keep the moisture content smaller than 0.1wt%.
    一般不需干燥。如受潮,在90℃條件下干燥2-3小時,或在70-80℃條件下干燥3-4小時,保持樹脂含水量小于0.1wt%后再使用。
     
    Physical and Electrical Properties   物理及電氣性能
    Item
    試驗項目
    Unit
    單位
    Typical Data典型值
    EP-3001 EP-3002 EP-3003
    Density at 23℃  23℃密度 g/cm3 0.918 1.09 0.95
    Hardness  硬度 Share A 92 90 87
    Melt Flow Index 熔體流動速率2.16kg×210℃ g/10min 0.39 0.52 ----
    Tensile Strength  拉伸強度 MPa 17 15.2 10.2
    Spring Back  回彈性 % 43 38 32
    Elongation at Break  斷裂伸長率 % 542 460 185
    Break Set  扯斷永久變形 % 104 ---- ----
    Compression Set
    壓縮永久變形
    70℃×22hr % 37.5 ---- ----
    100℃×22hr % 42 ---- ----
    Abrasion
    磨耗量(阿克。
    cm3/1.61kM 0.96 0.62 ----
    Ozone Resistance Aging
    耐臭氧老化
    50×10-8
    Tension 20%
    40℃×72hr
    No crake
    無裂紋
    No crake
    無裂紋
    No crake
    無裂紋
    Low Temperature Impact
    低溫沖擊
    -30℃ Pass
    通過
    Pass
    通過
    Pass
    通過
    Brittleness Temperature
    脆性溫度
    -50 -44 -45.5
    Air Aging Condition
    熱空氣老化條件
    150℃×168h
    Variation of Tensile Strength
    拉伸強度變化率
    % +18.3 +25.5 +15.5
    Variation of Elongation
    斷裂伸長變化率
    % -13.7 -14.2 -17.1
    Volume Resistivity 體積電阻率 Ω.m 4×1012 2.5×1012 ----
    耐油性能
    Oil Resistance Properties
     
    ASTM 1# Oil
    70℃x168h
    Retention of Tensile Strength
    拉伸強度保持率
    % ---- 80 78
    Retention of Elongation伸長率保持率 % ---- 79 74
    Variation of Volume
    體積變化率
    % ---- +8.5 +9.6
    耐油性能
    Oil Resistance Properties
     
    ASTM 2# Oil
    120℃x24h
    Retention of Tensile Strength
    拉伸強度保持率
    % ---- 51.6 53
    Retention of Elongation
    伸長率保持率
    % ---- 32.2 31.5
    Variation of Volume
    體積變化率
    % ---- 76 72
     

    在线成本人动漫视频网站-大香伊蕉在人线国产动画-老司机67194在线接播放-中文欧美亚洲欧日韩范冰冰-2019中文字幕乱码在线播放-国语自产精品视频在视频